IMCO Marine

Hose Kit 1 SR-8-5-13 Ram or 2 SR-8-1-13 Rams, 1 Helm

HELM CONTROL & HOSE KIT W/ELECTRIC PUMP "2.94 OR 5.2 TURNS LOCK TO LOCK"

Hose Kit 2 SR-8-1-13 Rams, 1 Pump, 1 Helm. 1 Filter

Hose Kit 2 SR-8-1-13 Rams, 2 Pumps, 1 Helm

HELM CONTROL & HOSE KIT "PUMP ASSIST" "3.25 TURNS LOCK TO LOCK"

Hose Kit Brazil Control Valve, Long Hoses

BRAZIL CONTROL VALVE APPLIES TO ALL EFI ENGINE PACKAGES 1994 AND LATER "FOR BOATS EXCEEDING 70 MPH A FULL HYDRAULIC HOSE KIT IS RECOMMENDED"

HK-12 Hose Kit Includes:

• (1) HCK-17: Brazil manifold assembly
• (156") HO-1: 5/16" HP Hose
• (4) FA-3: Hose End -6 JIC to 5/16" HP
• (1) FA-35: Hose Fitting -6 Mandrel.

Hose Kit Brazil Control Valve, Short Hoses

BRAZIL CONTROL VALVE APPLIES TO ALL EFI ENGINE PACKAGES 1994 AND LATER "FOR BOATS EXCEEDING 70 MPH A FULL HYDRAULIC HOSE KIT IS RECOMMENDED"

For parts list, and to buy replacement parts click here

Hose Kit Saginaw Control Valve, Long Hoses

"FOR BOATS EXCEEDING 70 MPH A FULL HYDRAULIC HOSE KIT IS RECOMMENDED" SAGINAW CONTROL VALVE APPLIES TO ALL HIGH PERFORMANCE ENGINE PACKAGES 1999 AND EARLIER AND TO ALL ENGINE PACKAGES 1994 AND EARLIER

Hose Kit Saginaw Control Valve, Short Hoses

"FOR BOATS EXCEEDING 70 MPH A FULL HYDRAULIC HOSE KIT IS RECOMMENDED" SAGINAW CONTROL VALVE APPLIES TO ALL HIGH PERFORMANCE ENGINE PACKAGES 1999 AND EARLIER AND TO ALL ENGINE PACKAGES 1994 AND EARLIER

For parts list, and to buy replacement parts click here

Imco 4" Rolled Edge (Bullnose) Exhaust Tip - (Sold in pairs)

These rolled edge stainless steel tips are perfect in many applications where safety is a concern Popular in above swim step location because their rolled edge provides a blunt edge These tips have flaps installed They will not accept slip-in silencers.

Imco Tie Bar Replacement Part. 2 per clevis joint, 4 per tie bar/ steering ram assembly. Sold and priced in a package of 4 each

Imco Tie Bar Replacement Part. Clevis Joint 4 per gimbal assembly.Comes with Clevis, Clevis Bolt, Nut, & 2 Bushings. Priced per 1 Clevis Joint

IMCO Drive - SCX Upper with SC Lower with 1-1/4" Prop Shaft

This complete outdrive kit allows you to convert from your stock Bravo drive to Imco's SCX upper with an SC lower. The kit comes with the SCX upper, your choice of an SC lower, helmet kit, drive reservoir.

Engineered from scratch for high horsepower/high torque engines, IMCO's SCX.

• No transmission needed. Cone clutch shifts internally.
• Fits Bravo HD gimbal with helmet change.
• Larger net-forged, 1 piece gears and oversized bearings.
• Larger clutch.
• Internal water cooling with built-in drive shower.
• Giant 5 quart oil capacity.
• 1-1/4" Prop Shaft
• This item does not ship UPS, Please Call To Order.
• All new, oversized heavy-duty components (bearings, gears, shafts, and case).
• 2+ years of research, design, development and testing.
• 3 gear ratios available 1:25, 1:34, 1:50.
• Accept standard Bravo style propellers.
• 4 lengths available, standard length, 1", 2", or 3" shorter

For Replacement Parts:
SCX Upper Case Click Here
SCX Upper Gear Click Here
SC Lower   Click Here

NOTE: These parts & unit have no warranty.

NOTE: This page is setup so you can pre-configure your Drive before calling to place an order. Due it's cost this part cannot be purchased online.

IMCO Drive - SCX Upper with SC Lower with 1-1/4" Prop Shaft - ITS Steering

This complete outdrive kit allows you to convert from your stock Bravo drive to Imco's SCX upper with an SC lower. The kit comes with the SCX upper, your choice of an SC lower, helmet kit, drive reservoir.

Engineered from scratch for high horsepower/high torque engines, IMCO's SCX.

• No transmission needed. Cone clutch shifts internally.
• Fits Bravo HD gimbal with helmet change.
• Larger net-forged, 1 piece gears and oversized bearings.
• Larger clutch.
• Internal water cooling with built-in drive shower.
• Giant 5 quart oil capacity.
• 1-1/4" Prop Shaft
• This item does not ship UPS, Please Call To Order.
• All new, oversized heavy-duty components (bearings, gears, shafts, and case).
• 2+ years of research, design, development and testing.
• 3 gear ratios available 1:25, 1:34, 1:50.
• Accept standard Bravo style propellers.
• 4 lengths available, standard length, 1", 2", or 3" shorter

For Replacement Parts:
SCX Upper Case Click Here
SCX Upper Gear Click Here
SC Lower   Click Here

NOTE: These parts & unit have no warranty.

NOTE: This page is setup so you can pre-configure your Drive before calling to place an order. Due it's cost this part cannot be purchased online.

SCX4 Complete Surface Drive

This unit comes with the helmet kit and drive reservoir.

4" Shorter than standard SC Drive, 2" shorter than SCX drive.

Engineered from scratch for high horsepower/high torque engines

• No transmission needed. Cone clutch shifts internally.
• Fits Bravo HD gimbal with helmet change.
• Larger net-forged, 1 piece gears and oversized bearings.
• Larger clutch.
• Internal water cooling with built-in drive shower.
• Giant 5 quart oil capacity.
• 3 gear ratios available 1:25, 1:34, 1:50.
• 2 prop shafts available 1 7/16" or Mercury Racing #6

For Replacement Parts:
SCX4 Lower Click Here
SCX4 Upper Case Click Here
SCX4 Upper Gear Click Here

NOTE: These parts & unit have no warranty.

NOTE: This page is setup so you can pre-configure your Drive before calling to place an order. Due it's cost this part cannot be purchased online.

IMCO Drive Oil Reservoir

The new IMCO drive oil reservoir is designed to install perpendicular on a 12º transom. It is constructed of billet aluminum and 1/4" wall clear acrylic. All hardware is stainless steel. The IMCO drive oil reservoir has an easy fill cap and can be easily disassembled and reassembled for cleaning. The reservoir comes either polished or polished and clear anodized. Fitting are provided. Holds up to 1 1/2 qt.

IMCO Drive SC Upper with SC Lower with 1-1/4" Prop Shaft

This unit is a complete IMCO SC Drive. You can configure this drive to fit your particular needs by choosing between the different colors, gear ratio's and the lengths of the lower unit that are offered.

The Billet Aluminum top cap is supported by eight bolts with a controlled water-circulation system and built in spray nozzles to provide maximum cooling to the external upper gear case.

The steel tower in the floor is stabilized through internal lateral support beams to eliminate tower flex and gear deflection.

IMCO has developed a rigid pinion and bearing pack assembly with non-elastic shims to provide the correct rolling torque while stabilizing both input yoke and pinion. Tightened to 75 lb/ft, the pinion assembly is held in place by our plated steel ujoint retainer nut through a direct load-bearing path.

For Replacement Parts:
SC Lower Click Here
SC Upper Case Click Here
SC Upper Gear Click Here

NOTE: These parts & unit have no warranty.

NOTE: This page is setup so you can pre-configure your Drive before calling to place an order. Due to its cost this part cannot be purchased online.

IMCO Drive SC Upper with SC Lower with 1-7/16" Prop Shaft

This unit is a complete IMCO SC Drive. You can configure this drive to fit your particular needs by choosing between the different colors, gear ratio's and the lengths of the lower unit that are offered.

The Billet Aluminum top cap is supported by eight bolts with a controlled water-circulation system and built in spray nozzles to provide maximum cooling to the external upper gear case.

The steel tower in the floor is stabilized through internal lateral support beams to eliminate tower flex and gear deflection.

IMCO has developed a rigid pinion and bearing pack assembly with non-elastic shims to provide the correct rolling torque while stabilizing both input yoke and pinion. Tightened to 75 lb/ft, the pinion assembly is held in place by our plated steel ujoint retainer nut through a direct load-bearing path.

For Replacement Parts:
SC Lower Click Here
SC Upper Case Click Here
SC Upper Gear Click Here

NOTE: These parts & unit have no warranty.

NOTE: This page is setup so you can pre-configure your Drive before calling to place an order. Due to its cost this part cannot be purchased online.

IMCO Drive SCX Upper with SC Lower - 1-7/16" Prop Shaft - ITS Steering

This complete outdrive kit allows you to convert from your stock Bravo drive to Imco's SCX upper with an SC lower. The kit comes with the SCX upper, your choice of an SC lower, helmet kit, drive reservoir.

Engineered from scratch for high horsepower/high torque engines, IMCO's SCX.

• No transmission needed. Cone clutch shifts internally.
• Fits Bravo HD gimbal with helmet change.
• Larger net-forged, 1 piece gears and oversized bearings.
• Larger clutch.
• Internal water cooling with built-in drive shower.
• Giant 5 quart oil capacity.
• 1-7/16" Prop Shaft
• This item does not ship UPS, Please Call To Order.
• All new, oversized heavy-duty components (bearings, gears, shafts, and case).
• 2+ years of research, design, development and testing.
• 3 gear ratios available 1:25, 1:34, 1:50.
• Accept standard Bravo style propellers.
• 4 lengths available, standard length, 1", 2", or 3" shorter

For Replacement Parts:
SCX Upper Case Click Here
SCX Upper Gear Click Here
SC Lower Click Here

NOTE: These parts & unit have no warranty.

NOTE: This page is setup so you can pre-configure your Drive before calling to place an order. Due it's cost this part cannot be purchased online.