421-05-8034 Gimbal Ring Kit Silver Gimbal Ring Kit Silver (Mercury Gimbal) Must be used with Hydraulic Steering
| Kit Includes |
| Qty |
Part # |
Description |
| 1 |
05-1298 |
Gimbal Ring Silver |
| 1 |
05-2305 |
Gimbal Shaft Swivel Upper (Merc) |
| 1 |
05-6310 |
Washer Replacement tiller Arm |
| 1 |
08-121300001 |
3/4" S/S AN Washer |
| 1 |
08-091306001 |
3/4-16 Thin Nylock Nut |
| 1 |
05-3320 |
Lower Swivel Pin |
| 1 |
10-7004 |
Bushing (Lower Swivel Pin) |
| 2 |
08-070806131 |
3/8-16 x 2 1/4" 12 pt Bolt |
| 2 |
05-2307 |
Gimbal Hinge Pin HP |
| 8 |
08-070604041 |
1/4-20 x .50 12 Point Bolt S/S |
| 1 |
05-3611 |
Front Trim Cylinder Pin |
| 2 |
05-6002 |
Washer Trim Pin (Big Hole) |
| 2 |
05-6004 |
Washer Trim Pin (Small Hole) |
| 2 |
08-080904001 |
7/16-20 Nylock Nut S/S |
| 2 |
08-211300001 |
3/4" Snap Ring Extra Thick S/S |
| 1 |
05-2601 |
Clip Lower Pin |
| 1 |
08-010705061 |
5/16-18 x 3/4" HH Bolt S/S |
| 1 |
05-2017 |
6" Bonding Wire |
| 1 |
08-010403031 |
10-24 x 3/8" HH Bolt S/S |
|
|
421-05-2003 Water HoseGimbal Water Hose
|
|
421-05-2010 Grease Short Strap Cap FittingGrease Short Strap Cap Fitting
|
|
421-01-2066 Guide Pads (Port & Starboard)
1 pair per Upper Case Assembly
|
|
421-04-2295B IMCO Heavy Duty Bravo Bellhousing
IMCO's new flywheel
bellhousing is a direct replacement for installations using Bravo, XR, XZ
and IMCO XTreme Advantage SC drives. The new bellhousing is
reinforced in all critical areas with additional gusseting around the
motor mount area. There is a flange at the top of the housing for
accessory mounting. Better....and still affordable.
|
|
421-01-3267 This shaft is cross drilled to create it's own internal central-fed lubrication system Better oiling promotes longer, more reliable duty cycle A must on high performance applications. This model is 2" Shorter.
|
|
421-02-2550 Heim JointHeim Joint 1/4-28 & Nut
|
|
421-HC-2 Helm Control 120 CC (1 or 2 Pumps) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-8 Helm Control 145 CC (1 or 2 Pumps) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-3 Helm Control 160 CC (1 Pump Drill Orifice 11/64” or 2 Pumps) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-9 Helm Control 185 CC (2 Pumps) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-4 Helm Control 230 CC (2 Pumps)
HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
4.2 turns lock to lock with dual #6.
|
|
421-HC-10 Helm Control 295 CC (2 Pumps)
HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
3.3 turns lock to lock with dual #6.
|
|
421-HC-13 Helm Control 50 CC (1 or 2 Pumps) (((A=Left B=Right)) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-1 Helm Control 75 CC (1 or 2 Pumps) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-7 Helm Control 95 CC (1 or 2 Pumps) HELM CONTROL SPECIFICATIONS MERCURY PUMP SPECIFICATIONS 1. FLOW RATE 2 TO 8 GPM 1. FLOW RATE 1 1/2 TO 3 1/2 GPM 2. MAX PRESSURE 2500 PSI 2. MAX PRESSURE 1300 PSI 3. OPEN CENTER NON LOAD REACTION 4. 3/4" O-RING PORTS
|
|
421-HC-12 Helm Control Remote Fill Kit
|
|
421-HK-1 Helm Kit 1 SR-8-5-13 Ram, 1 Pump, 1 Helm HELM CONTROL & HOSE KIT "PUMP ASSIST" "2.94 TURNS LOCK TO LOCK"
|
|
421-HP-10 Helm Post Assembly 15° x 11.00” Dashboard to Hub Face Polished 316 SS "STEERING WHEEL AND HELM CONTROL NOT INCLUDED"
|
|
421-HP-7 Helm Post Assembly 15° x 8.000” Dashboard to Hub Face Polished 316 SS
"STEERING WHEEL AND HELM CONTROL NOT INCLUDED"
|
|
