Livorsi Marine

1/2" O.D. x 1/4" I.D. Push-On High Pressure Speedometer Hose 25 ft. Roll

No speedometer installation is complete without high pressure pitot tubing. This high quality flexible pitot hose is available in both 1/8" and 1/4" and don’t forget that clamshell to cover the transition your hose will make thru the hull.

Note: Sold in 25 ft. Rolls!

1/4" Cutout LED Warning Light

1/4" O.D. x 1/8" I.D. Push-On High Pressure Speedometer Hose 25 ft. Roll

No speedometer installation is complete without high pressure pitot tubing. This high quality flexible pitot hose is available in both 1/8" and 1/4" and don’t forget that clamshell to cover the transition your hose will make thru the hull.

Note: Sold in 25 ft. rolls!

1/4", 3/8", 1/2" Bushing Kit for Livorsi Senders

1/8" NPT 100-280F Water Temperature Sender For Livorsi Gauges (Mercury Match)

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

1/8" NPT 140 to 340F Oil Temperature Sender For Livorsi Gauges

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

• 16" Stroke.
• Overall Length Closed is 22-3/8".
• Strong eyelet mount allows a wide range of angles for easy installation.
• Marine grade stainless steel housing
• Sealed precision die cast housing.
• 12 VDC
• Safe working dynamic load limit of 400 lbs.*
• Static Limit of 500 lbs.*
• Heavy duty, sealed ball bearing motor allows for locking of hatches, won’t open at high speeds
  
• NOTE: Please verify your dimensions. Actuators that have been installed are NON returnable!

*Static loading refers to the load on an actuator when it is in a fixed or stationary condition. The static load capacity of an actuator refers to how much weight the actuator can safely hold without back driving or causing damage. Dynamic load is the load the actuator sees when it is powered and extending or retracting. The dynamic load capacity of an actuator refers to how much the actuator can push or pull. Placing an actuator closer to the hatch hinge point will require the actuator to work harder than installing it further out.

3/8" Cutout LED Warning Light, Super Bright

3/8" NPT 100-280F Water Temperature Sender For Livorsi Gauges (Mercury Match)

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

• 4" Stroke.
• Overall Length Closed is 11-7/8".
  
• Strong eyelet mount allows a wide range of angles for easy installation.
• Marine grade stainless steel housing
• Sealed precision die cast housing.
• 12 VDC
• Safe working dynamic load limit of 400 lbs.*
• Static Limit of 500 lbs.*
• Heavy duty, sealed ball bearing motor allows for locking of hatches, won’t open at high speeds
  
• NOTE: Please verify your dimensions. Actuators that have been installed are NON returnable!

*Static loading refers to the load on an actuator when it is in a fixed or stationary condition. The static load capacity of an actuator refers to how much weight the actuator can safely hold without back driving or causing damage. Dynamic load is the load the actuator sees when it is powered and extending or retracting. The dynamic load capacity of an actuator refers to how much the actuator can push or pull. Placing an actuator closer to the hatch hinge point will require the actuator to work harder than installing it further out.

5/16" Cutout LED Warning Light

• 8" Stroke.
• Overall Length Closed is 15-7/8".
  
• Strong eyelet mount allows a wide range of angles for easy installation.
• Marine grade stainless steel housing
• Sealed precision die cast housing.
• 12 VDC
• Safe working dynamic load limit of 400 lbs.*
• Static Limit of 500 lbs.*
• Heavy duty, sealed ball bearing motor allows for locking of hatches, won’t open at high speeds
  
• NOTE: Please verify your dimensions. Actuators that have been installed are NON returnable!

*Static loading refers to the load on an actuator when it is in a fixed or stationary condition. The static load capacity of an actuator refers to how much weight the actuator can safely hold without back driving or causing damage. Dynamic load is the load the actuator sees when it is powered and extending or retracting. The dynamic load capacity of an actuator refers to how much the actuator can push or pull. Placing an actuator closer to the hatch hinge point will require the actuator to work harder than installing it further out.

4 Pin Connector & Wire Harness 18 inch, 3 Pack for Livorsi Single Outboard Engine Gauge Kits

The Plug-In Connector feature which makes Livorsi's new Deutsch gauges unique make installation a breeze, saving you a lot of rigging time & frustration. This 3 pack goes perfectly with one of our Livorsi Engine Gauge Kits.

NOTE: Connectors sold separately from gauges. Most Livorsi Gauges except GPS Speedos and Mechanical Gauges will require this connector!

4 Pin Connector & Wire Harness 18 inch, 5 Pack for Livorsi Gauge Kits

The Plug-In Connector feature which makes Livorsi's new Deutch gauges unique make installation a breeze, saving you a lot of rigging time & frustration. This 5 pack goes perfectly with one of our Livorsi Gauge Kits.

NOTE: Connectors sold separately from gauges. Most Livorsi Gauges except GPS Speedos and Mechanical Gauges will require this connector!

4 Pin Connector & Wire Harness 18 inch, 9 Pack for Livorsi Dual Engine Gauge Kits

The Plug-In Connector feature which makes Livorsi's new Deutsch gauges unique make installation a breeze, saving you a lot of rigging time & frustration. This 9 pack goes perfectly with one of our Livorsi Dual Engine Gauge Kits.

NOTE: Connectors sold separately from gauges. Most Livorsi Gauges except GPS Speedos and Mechanical Gauges will require this connector!

High Vibration Electric Fuel Pressure Sender
Works in either 0-100 PSI, 0-60 PSI or 0-90 PSI for Autometer or Livorsi Gauges

Quite possibly one of the most important things to monitor while making those high speed runs. Everyone knows fuel pressure is critical so always run the correct senders to watch your gauge. All senders are 1/8" NPT.

High Vibration Electric Fuel or Water Pressure Sender
0-15 PSI, Autometer or Livorsi Gauges

Quite possibly one of the most important things to monitor while making those high speed runs. Everyone knows fuel pressure is critical so always run the correct senders to watch your gauge. All senders are 1/8" NPT.

LED Lights for Livorsi Gauges, Wedge Style. 12.8v. LED lights outshine and outlast incandescent bulbs. NOTE: These do not work with standard Livorsi ELECTRIC DCS 2-1/16" gauges. On those gauges the led is soldered to the circuit board and can only be changed when the gauge is built. These lights only work on 3-3/8" and 4-5/8" Tachs and Speedos, all monster size DC 2-5/8" gauges and MECHANICAL DCS 2-1/16" gauges. Note that 4-5/8" Tachs and Speedos have 2 bulbs per gauge.

Lighted Switch, On / Off / On Double Pole

These rocker style switches offer the latest in modern styling. Each switch is both dust and moisture protected. This switch is designed to snap into a .830" x 1.450" rectangular hole and is rated at 20 amps. These switches use heavy duty 1/4" connectors.