The Blower Shop

Rear Bearing plate o-rings are made out of a rubber based material. To be used on The Blower Shop™ rear Bearing plate caps. Sold in Pairs.

• Weight: 0.1 lbs
• Dimensions: 3×3×.1 in

Billet Grease Covers, comes in a pair.

• Weight: 1 lbs
• Dimensions: 4×4×4 in
• 71 / Low Profile: 71 Series

Idler Bracket Assembly Blower Mount

• Billet aluminum

• Better selection - 4" and 6" idler pulleys available

• Standard blower mount bracket • Competition block mount bracket
• Swing arm bracket

These deep groove ball bearings Idler Pulley Bearings are designed for a longer life with high performance and reliability. This item comes as a pair.

• Weight: 1 lbs
• Dimensions: 2×2×1.25 in
• 71 / Low Profile: 71 Series

• Weight: 0.1 lbs
• Dimensions: 14×6×.1 in

Inlet gasket without screen.

• Weight: 1 lbs
• Dimensions: 14×6×1 in
• Single or 10 Pack: Single Inlet Gasket, 10 Pack Inlet Gasket
• 71 / Low Profile: Low Profile

Feature an adjustable heim end design and needle bearings for long life and smooth throttle operation. To prevent slippage the shaft and arms are serrated and there is also a set of two extra long steel studs to mount the lower cable bracket to the left side of the blower. Click Here For Instructions

• Weight: 4 lbs
• Dimensions: 14×4×2 in
• Linkage Kits: 250 Dual Sideways Kit, Dual Inline (8 5/8") Kit, Dual Sideways (4150 / 4500)
• 71 / Low Profile: 71 Series
• Fuel Delivery: Carb

Feature an adjustable heim end design and needle bearings for long life and smooth throttle operation. To prevent slippage the shaft and arms are serrated and there is also a set of two extra long steel studs to mount the lower cable bracket to the left side of the blower. Click Here For Instructions

• Weight: 3 lbs
• Dimensions: 14×4×2 in
• Linkage Kits: 250 Dual Sideways Kit, Dual Inline (8 5/8") Kit, Dual Sideways (4150 / 4500)
• 71 / Low Profile: 71 Series
• Fuel Delivery: Carb

For Kuhl, Hampton dual carb adapters where the carbs go up and forward, rear carb goes up and back. Centerline to centerline 12″ – 12 1/4″ Not the rod out of the 4350 linkage kit.

• Weight: 1 lbs
• Dimensions: 15×7×2 in
• 71 / Low Profile: 71 Series
• Fuel Delivery: Carb

192/250 Billet snout with the snout spring and swing arm.

• Weight: 5 lbs
• Dimensions: 14×10×6 in
• Arm Length: Short 3.95", Medium 4.95", Long 7.07", MERC 575 3.80"
• 71 / Low Profile: Low Profile

Heat treated main shaft for the 192/ 250 superchargers.

• Weight: 5 lbs
• Dimensions: 14×10×6 in
• Length: Short 5.6", Medium 6.6", Long 8.7"
• 71 / Low Profile: Low Profile

This plate is for the use of 250 Supercharger on a TBS Billet LS Manifold Base. Includes: 1ea – Top Plate (250 Blower) 10ea – 5/16-18 x 1″ S.H.C.S. Stainless Steel 2ea – .308 x 1″ Dowel Pins 1ea – #9300 250 O-ring 5.5ft – #4903 1/8″ O-ring cord stock Note: #2595 192/250 Stainless Steel Stud Kit NOT INCLUDED

• Weight: 10 lbs
• Dimensions: 22×15×7 in
• 71 / Low Profile: Low Profile
• Engine Model: LS 1/LS 3

This plate is for the use of 71 Series Supercharger on a TBS Billet LS Manifold Base. Includes: 1ea – Top Plate (71 Series Blower) 10ea – 5/16-18 x 1″ S.H.C.S. Stainless Steel 2ea – .308 x 1″ Dowel Pins 1ea – #4900 Universal Base Gasket 5.5ft – #4903 1/8″ O-ring cord stock Note: #2590 Aluminum Stud and Nut Kit NOT INCLUDED

• Weight: 10 lbs
• Dimensions: 22×15×7 in
• 71 / Low Profile: 71 Series
• Engine Model: LS 1/LS 3

These Plates are used to block off the EFI Ports machined in a TBS Billet LS manifold that has been machined for Direct Port Injection. Includes: 2ea – Block Off Plates 6ea – 1/4-20 x 3/4″ S.H.C.S. Stainless Steel 8ea – O-rings

• Weight: 3 lbs
• Dimensions: 16×12×3 in
• 71 / Low Profile: 71 Series
• Engine Model: LS 1/LS 3
• Fuel Delivery: EFI

• Weight: 4 lbs
• Dimensions: 16×12×3 in
• 71 / Low Profile: 71 Series
• Engine Model: LS 1/LS 3
• Fuel Delivery: EFI

Eight pack of O-rings for LS intake ports.

• Weight: 0.1 lbs
• Dimensions: 4×4×.3 in
• Engine Model: LS 1/LS 3

LS1 / LS3 Lower Hub 1.25″ WIDE – DESIGNED FOR USE WITH ATI CORVETTE BALANCER

• Weight: 4 lbs
• Dimensions: 6×6×3 in
• Finish: Polished, Black Hard Anodized
• Engine Model: LS 1/LS 3

LS1 CATHEDRAL PORT KIT- EFI DIRECT PORT FOR ATI CORVETTE BALANCER (#2632) TBS LS Billet aluminum CNC machined intake manifold is designed for LS1 CATHEDRAL PORT applications. This manifold is drilled for direct EFI porting directly into the sides of the manifold. The complete drive kit includes all parts and drive accessories required for assembly in conjunction with 71-Series supercharger using an ATI Corvette Balancer. It designed to fit a stock LS water pump application. TBS 71-Series Superchargers: https://theblowershop.com/tbs-roots-style-superchargers/71-series-blowers/

• Weight: 35 lbs
• 71 / Low Profile: 71 Series
• Engine Model: LS 1/LS 3
• Fuel Delivery: EFI
• Port Size: Cathedral

(2631) LS1 Cathedral Port- Drive Kit Builder for ATI Corvette Balancer This Billet aluminum CNC machined intake manifold is designed for LS1 CATHEDRAL PORT applications. This complete drive kit includes all parts and drive accessories required for assembly in conjunction with 71-Series supercharger using an ATI Corvette Balancer. This kit is designed to fit a stock LS water pump application. TBS 71-Series Superchargers: https://theblowershop.com/tbs-roots-style-superchargers/71-series-blowers/

• Weight: 35 lbs
• 71 / Low Profile: 71 Series
• Engine Model: LS 1/LS 3
• Port Size: Cathedral

LS3 CATHEDRAL PORT KIT- EFI DIRECT PORT FOR ATI CORVETTE BALANCER (#2632) TBS LS Billet aluminum CNC machined intake manifold is designed for LS3 RECTANGLE PORT applications. This manifold is drilled for direct EFI porting directly into the sides of the manifold. The complete drive kit includes all parts and drive accessories required for assembly in conjunction with 71-Series supercharger using an ATI Corvette Balancer. It designed to fit a stock LS water pump application. TBS 71-Series Superchargers: https://theblowershop.com/tbs-roots-style-superchargers/71-series-blowers/

• Weight: 35 lbs
• 71 / Low Profile: 71 Series
• Engine Model: LS 1/LS 3
• Fuel Delivery: EFI
• Port Size: Rectangle