UFlex

V45 White 3 Spoke Ultraflex Steering Wheel

These are 11". They are smaller than the traditional marine wheel. Entire wheel except internal hub is made from Thermoplastic material, standard 3/4" taper hub built into wheel and is non-removable. Hub and center cap included.

Need help installing your new steering wheel? Check out this handy tutorial!

Nisida Aluminum Spoke Steering Wheel

• 13.8" Diameter
• Black Air Leather Look Grip
• Polished, Silver or Black Spokes
• 6 Bolt Pattern
• Includes hub for 3/4" Tapered shaft.

Need help installing your new steering wheel? Check out this handy tutorial!

Antigua Steering Wheel, 3 Spoke, 13.7" Diameter, 

All U-FLEX steering wheels meet the EEC directive 94/25 requirements about pleasure boats. All steering wheels are CE marked in conformity with the EN 28848 – EN 29775 and ABYC P22 safety standards.

• Thermoplastic antishock material
• Standard 3/4’’ taper
• Hub included
• Meet with the EN 28848 and ABYC P22 standards

All Antigua steering wheels are provided with an exclusive hub that easily allows the steering wheel to always be aligned properly.

Need help installing your new steering wheel? Check out this handy tutorial!

• Standard 3/4’’ taper
• 13.8" diameter wheel
• Hub included
• All ULTRAFLEX steering wheels meet the EEC directive 94/25 requirements about pleasure boats.
• All steering wheels are CE marked in conformity with the EN 28848 – EN 29775 and ABYC P22 safety standards.

Need help installing your new steering wheel? Check out this handy tutorial!

Non-Magnetic Stainless Steel Cross Spokes Steering Wheel, 13.8" Diameter, Black Polyurethene Grip

Non-Magnetic Stainless Steel Cross Spokes Steering Wheel, 13.8" Diameter, Buckskin Polyurethene Grip

For complete control of engine trim and tilt, trim tabs, jackplates, PowerPole(R) and other on board systems, the innovative Paddle Trim system is the answer.

Adaptable to existing front mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.

FEATURES

• Available both in single and dual versions (for either two equal or two different outputs). 
• Both single or dual paddle can be positioned at various angles for the most confortable choice. 
• Equipped with one water proof “MOM.ON-OFF-MOM.ON switch ( 2 switches on dual version). 
• Max load 5 Amp @ 12VDC.
• For loads exceeding 5 Amp we recommend the use of the KTR - 42860S kit relay.
• Uflex^® trim tabs require the use of the KTR - 42860S kit relay.
• Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). 
• Easy to install on the following Ultraflex^® steering systems: front and tilt mount hydraulic helms and tilt mount mechanical helms
• Wiring harness, labels and mounting hardware kit are included. The mounting plate, which differs between front and tilt mount. Installation, is ordered separately.

For complete control of engine trim and tilt, trim tabs, jackplates, PowerPole(R) and other on board systems, the innovative Paddle Trim system is the answer.

Adaptable to existing front mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.

FEATURES

• Available both in single and dual versions (for either two equal or two different outputs). 
• Both single or dual paddle can be positioned at various angles for the most confortable choice. 
• Equipped with one water proof “MOM.ON-OFF-MOM.ON switch ( 2 switches on dual version). 
• Max load 5 Amp @ 12VDC.
• For loads exceeding 5 Amp we recommend the use of the KTR - 42860S kit relay.
• Uflex^® trim tabs require the use of the KTR - 42860S kit relay.
• Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). 
• Easy to install on the following Ultraflex^® steering systems: front and tilt mount hydraulic helms and tilt mount mechanical helms
• Wiring harness, labels and mounting hardware kit are included. The mounting plate, which differs between front and tilt mount. Installation, is ordered separately.

3300 Style 10-32 Threaded Cable. Stainless Steel Hardware. 3.4” (87mm) Stroke. 0.27” (7mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories.

Note: For highest performance and reliability use Hardin Marine 3300 / 33C Cables.

Mach Zero 3300 Style 10-32 Threaded Cable

• 3.4” (87mm) Stroke.
• 0.31” (8mm) Diameter.
• Stainless Steel Hardware.
• For use with inboard, sterndrive, and outboard engines with appropriate accessories.

Note: For highest performance and reliability use Hardin Marine 3300 / 33C Cables.

Evinrude, Johnson, Pre 1979 OMC Control Cable. Brass Hardware. 3.1” (80mm) Stroke. 0.27” (7mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories.

Mach Series Evinrude, Johnson, Post 1979 OMC Control Cable. Stainless Steel Hardware. 3” (75mm) Stroke. 0.31” (8mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories. Blue Mach Series Jacket ideal for high performance applications, long cable runs, and complex routings.

Mach Series Mercury and Mercruiser Control Cable. Stainless Steel Hardware. 3.75” (95mm) Stroke. 0.31” (8mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories.

Mach Series Mercury and Mercruiser Generation II. Stainless Steel Hardware. 3.4” (85mm) Stroke. 0.31” (8mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories. Blue Mach Series Jacket ideal for high performance applications, long cable runs, and complex routings.

Mercury and Mercruiser Control Cable. Brass Hardware. 3.75” (95mm) Stroke. 0.27” (7mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories.

Universal 10-32 Threaded Cable. Brass Hardware. 3.4” (87mm) Stroke. 0.27” (7mm) Diameter. For use with inboard, sterndrive, and outboard engines with appropriate accessories.

Hyco Front Mount Outboard System for 150hp and Less. Includes: UC94-OBF cylinder (Not suitable for HONDA®BF115 and BF130 engines and Mercury® Optimax TM75, 90, 115.) Available with Standard or Tilt Helm.

Featuring the unique split tilt tube rod that allows for installation of the UC94 cylinder without removing the engine the Hyco is an easy and affordable outboard hydraulic steering solution for boats with 150 horsepower and under. Coupled with the UP20 helm the Hyco offers effortless steering with 5 turns lock to lock. And it is applicable to almost all 2 and 4 stoke outboards engines.

This kit includes Hydraulic Ram, Hydraulic Helm and 2 Quarts of Oil.
Steering Wheel, Hose and fittings are sold separately!

See Application Guide on Additional Info Tab to make sure you order the correct cylinder.