495-231 1" Prop Seal Rebuild Kit
Fits: the 495-229 box
|
|
|
|
495-122 1" shaft log rebuild kit
Fits: the 495-211 box
|
|
495-232 1-1/8" Prop Seal Rebuild Kit
Fits: the 495-212 box
|
|
495-126 1-1/8" Rudder Box Rebuild Kit
Fits: the 495-216 box
|
|
495-123 1-1/8" shaft log rebuild kit
Fits: the 495-212 box
|
|
This Part has options, please click the button below to order.
500-03 + Option(s) Brass Rubber Prop Shaft Strut Bushing
Water lubricated prop shaft bushings. Other sizes available by request.
|
|
495-213 Cavitation Rod Seal Box 1"
New design 1” cavation rod seal (fits
standard 1” inside diameter hoses).
These rod seals are made to fit 1/2"
diameter cavation rods. Made from 6061-T6 Alum. They have 2 double
lip cup seals with a gap in between them for grease. A snap ring on
the front for containment and safety. The water side is an o-ring for
a total of 3 water seals.
|
|
495-214 Cavitation Rod Seal Box 1-1/4"
New design 1 1/4” cavation rod seal
(fits standard 1 1/4” inside diameter hoses).
These rod seals are made to fit 1/2"
diameter cavation rods. Made from 6061-T6 Alum. They have 2 double
lip cup seals with a gap in between them for grease. A snap ring on
the front for containment and safety. The water side is an o-ring,
for a total of 3 water seals.
|
|
495-229 Prop Shaft Seal Box 1"
Made from 6061-T6 aluminum with a beautiful machined finish that can be easily polished or anodized to match your existing hardware. They are approximately 2 1/8" diameter by 2 1/2" long.
Inside the aluminum housing are 3x double lip cup seals to keep the water out and a grease zerk on the outside body to grease the seal. The seals are held in the aluminum housing by a snap ring for safety. A standard size 1 3/4" hose fits from the rear, I also added rounded grooves to help the hose clamp bite into the housing and not slip off.
|
|
495-221 Prop Shaft Seal Box 1" Kit
Made from 6061-T6 aluminum with a beautiful machined finish that can be easily polished or anodized to match your existing hardware. They are approximately 2 1/8" diameter by 2 1/2" long.
Inside the aluminum housing are 3x double lip cup seals to keep the water out and a grease zerk on the outside body to grease the seal. The seals are held in the aluminum housing by a snap ring for safety. A standard size 1 3/4" hose fits from the rear, I also added rounded grooves to help the hose clamp bite into the housing and not slip off.
This kit includes the shaft seal, Two stainless steel hose clamps and 4" of hose.
|
|
495-212 Prop Shaft Seal Box 1-1/8"
Made from 6061-T6 aluminum with a machined finish. The prop shaft seal is
approximately 2-1/4" diameter by 2 1/2" long.
Inside the aluminum housing is 3 double lip cup seals to keep the water out
and a grease zert on the outside body to grease the seal. It's held in the
aluminum housing by a snap ring for safety. A standard size 1 3/4" hose
fits from the rear. Added rounded grooves to help the hose clamp
bite into the housing and not slip off.
|
|
495-222 Prop Shaft Seal Box 1-1/8" Kit
Made from 6061-T6 aluminum with a machined finish. They are approximately 3" diameter by 2-7/8" long. There is a lightly pressed in 2-1/3" dia. double sealed bearing with the inside diameter bored to 1.128" (to easily slip over your prop shaft). It’s held in the aluminum housing by a snap ring for safety.
Also inside the aluminum housing is a double lip cup seal to keep the water out and a grease zert on the outside body to grease the seal. A standard size 1 3/4" hose fits from the rear. Rounded grooves have been added to help the hose clamp bite into the housing and not slip off.
With this design there will be no more prop shaft wear of bushings to replace because it rides on a bearing.
This kit includes the shaft seal, Two stainless steel hose clamps and 4" of hose.
|
|

495-217 Round Rudder Box 1"
New
design. Made from 6061-T6 Aluminum that is machined finish.
Sealed
bearing design (just like the billet prop shaft log seals). No more
housings to wear out!!! The prop shaft rides on the bearing.
This
new rudder stuffing box has a standard 4 1/16” round mounting
flange. So it is a direct replacement for your older style stuffing
box. No mounting holes have been drilled, because every hull is
different and has a variety of hole sizes and patterns. All you have
to do is transfer punch the existing hole locations in your hull to
the rudder box and drill the size you need.
Fits
all standard 1 1/2” diameter thru hull holes. The 1 1/2” diameter
section, that goes thru the bottom of your hull long (1 3/4” long),
was left to accommodate any hull thickness. You will have to trim to
fit.
Overall
height of stuffing box inside the boat is 2 1/8”.
Starting
from the top of the stuffing box to the bottom features a snap ring
for safety to help retain the 1” sealed bearing that is bored a few
thousands larger than your rudder shaft.
Next
is an ample sized grease reservoir which is filled by the grease zert
located on the outside of the rudder box housing.
A
double lip grease cup seal is lightly pressed in as a second barrier
to keep water out. The first water barrier is a 1/8” diameter
o-ring that is below the grease cup seal.
|
|

495-215 Square Rudder Box 1"
New
design. Made from 6061-T6 Aluminum that is machined finish.
Sealed
bearing design (just like my billet prop shaft log seals). No more
housings to wear out!!! The prop shaft rides on the bearing.
This
new rudder stuffing box has a standard 3 5/16” square mounting
flange. So it is a direct replacement for your older style stuffing
box. No mounting holes have been drilled, because every hull is
different and has a variety of hole sizes and patterns. All you have
to do is transfer punch the existing hole locations in your hull to
the rudder box and drill the size you need.
Fits
all standard 1 1/2” diameter thru hull holes. The 1 1/2” diameter
section, that goes thru the bottom of your hull long (1 3/4” long),
was left to accommodate any hull thickness. You will have to trim to
fit.
Overall
height of stuffing box inside the boat is 2 1/8”.
Starting
from the top of the stuffing box to the bottom features a snap ring
for safety to help retain the 1” sealed bearing that is bored a few
thousands larger than your rudder shaft.
Next
is an ample sized grease reservoir which is filled by the grease zert
located on the outside of the rudder box housing.
A
double lip grease cup seal is lightly pressed in as a second barrier
to keep water out. The first water barrier is a 1/8” diameter
o-ring that is below the grease cup seal.
|
|

495-216 Square Rudder Box 1-1/8"
New
design. Made from 6061-T6 Aluminum that is machined finish.
Sealed
bearing design (just like the billet prop shaft log seals). No more
housings to wear out!!! The prop shaft rides on the bearing.
This
new rudder stuffing box has a standard 3 5/16” square mounting
flange. So it is a direct replacement for your older style stuffing
box. No mounting holes have been placed, because every hull is
different and has a variety of hole sizes and patterns. All you have
to do is transfer punch the existing hole locations in your hull to
the rudder box and drill the size you need.
Fits
all standard 1 5/8” diameter thru hull holes. The 1 5/8” diameter
section, that goes thru the bottom of your hull long (1 3/4”
long), was left to accommodate any hull thickness. You will have to
trim to fit.
Overall
height of stuffing box inside the boat is 2 5/16”.
Starting
from the top of the stuffing box to the bottom features a snap ring
for safety to help retain the 1 1/8” sealed bearing that is bored a
few thousands larger than your rudder shaft.
Next
is an ample sized grease reservoir which is filled by the grease zert
located on the outside of the rudder box housing.
A
double lip grease cup seal is lightly pressed in as a second barrier
to keep water out. The first water barrier is a 1/8” diameter
o-ring that is below the grease cup seal.
|
|
This Part has options, please click the button below to order.
100-720- + Option(s) Standard Duty Stainless Steel Worm Gear Clamps
These are NOT cheap automotive-style band clamps They are a 100% stainless steel band, clamp, and screw. These clamps are designed to give years of trouble-free service. Don't trust anything but the best for your boat.
|
|
500-0232 Stuffing Box Hose
Hose for use with Stuffing Box, 4.5" Long, 1.75" ID, 2.25" OD. Clamps sold separate.
|
|
This Part has options, please click the button below to order.
100-720- + Option(s) Superduty Stainless Steel T-Bolt Band Clamps
T-bolt clamps are the very best clamp money can buy. They are virtually impervious to harsh elements and are super-strong. If you want the best,use T-bolt clamps. Available in many sizes from 1" to 6"
- 100-720-1000, use with 1" hard wall hose
- 100-720-1060, use with 1-1/4" hard wall hose
- 100-720-1120, use with 1-1/2" Fuel Fill hose
- 100-720-2000, use with 2" Fuel Fill hose
- 100-720-2120, use with 2-7/8" Exhaust hose
- 100-720-3000, use with 3" Exhaust hose
- 100-720-3120, use with 3-1/2" Exhaust hose
- 100-720-4000, use with 4" Exhaust hose
- 100-720-4120, use with 4-1/2" Exhaust hose
- 100-720-5000, use with 5" Exhaust hose
|
|
This Part has options, please click the button below to order.
500-024 + Option(s) Double Seal Prop Shaft Stuffing Box (For 1" Shafts Only)
This stuffing box incorporates double neoprene seals.
Water may be discharged into the stuffing box, further
lubricating the aqua lube bearing insert. For 1" shafts only. 1/8" NPT water discharge port .
|
|