Generic

• Solves coolant pressure issues in turns
• Specifically for multi-engine catamarans
• Maintains pressure when inner engine loses flow
• Improves reliability during maneuvering
• Prevents overheating in twin-engine applications

BMP Direct replacement to the Factory Mercury 450R Prop shaft this 300 M solid one piece construction shaft has 34% more strength. Zinc coated to prevent corrosion and features an upgraded tip for a cotter pin installation.

This prop hub is half the weight of a standard steel hub and it is perfectly balanced to a neutral weight which removes strain and stress from the prop shaft. It is compatible with a 1.25", 19 spline prop shaft found in LX and V8 Mercury’s (excluding 500R).

This direct bolt-on kit adds 5° of ignition timing for improved acceleration and increased top end MPH. The dual-sensor design lets you easily switch between 5° advanced timing and stock timing by simply swapping a plug. Premium 91-93 octane fuel is required when running the 5° advance setting. Switch back to stock timing when running REC-90 or lower-quality fuel. Fits 200/250/300/300R/450/500R

Beneteau Donut Collars

Size: 25mm or 30mm Sold: Each

Bennett actuators are strong but flexible nylon/fiberglass hydraulic cylinders. The piston-like arms push tabs into position. Fluid flows through a concealed hole in the upper hinge at the top of the actuator - thus eliminating external hoses subject to damage.

• A1101A is the standard


• A1101EX is an external line connection used in cases of total inaccessibility inside the transom


• A1200S designed for installations where space is limited

• A1101A is the standard


• A1101EX is an external line connection used in cases of total inaccessibility inside the transom


• A1200S designed for installations where space is limited

Description: "Actuator Assembly - Standard (13-3/4")"

Bennett actuators are strong but flexible nylon/fiberglass hydraulic cylinders. The piston-like arms push tabs into position. Fluid flows through a concealed hole in the upper hinge at the top of the actuator - thus eliminating external hoses subject to damage. All models provide a 2-1/2" stroke. Replacement actuators do not include hardware. Hardware kit H1170A is recommended when replacing an actuator assembly.

• Description: Actuator Assembly - Small Version (11-3/4")
• A1200S designed for installations where space is limited

Automatically retracts tabs when boat's ignition is turned off. Trailered boats have added defense from trim tab damage w/them "full-up" during hauling, trailering and storage. Assures trim tabs are all the way up every time boat is started if boat is not equipped w/trim tab indicators. Easily installs behind instrument panel. 12 volt.

• Superior seal design inspired by over 50 years of Bennett's proven success in hydraulic trimming techniques
• Robust, water-tight black nylon actuator provides trouble-free operation for years to come
• Completely waterproof, submersible and maintenance-free
• No external screws to cause leakage
• Description: Actuator w/Adjustable Upper Hinge, Volts: 12

• Superior seal design inspired by over 50 years of Bennett's proven success in hydraulic trimming techniques
• Robust, water-tight black nylon actuator provides trouble-free operation for years to come
• Completely waterproof, submersible and maintenance-free
• No external screws to cause leakage
• Description: Actuator w/Fixed Upper Hinge, Volts: 12

Economical, easy installation alternative to replacing Lenco actuator or purchasing an entire trim tab system. Uses existing Lenco trim planes. No need to patch or re-drill mounting holes. Bennett control fits and covers existing Lenco switch cutout.

• (1) V351HPU1 12V hydraulic power unit
• (2) A1101A actuators
• 20' hydraulic tubing
• (1) H1170LCHK Lenco conversion hardware kit
• (1) ES2000 rocker switch control w/22' wire harness
• (1) H1170A hardware kit

This control is ergonomically designed, water resistant and provides a positive "click" when the trim tabs are engaged. Its lock-out feature prevents user from pressing down on opposite directions at the same time. The control is easy to install, fitting into a single 2 1/2" hole.

Includes two 3" brass pipe nipples, two brass female elbows, two tube bending clips, six #14 x 1 1/2" full threaded screws, four 1/4-20 x 3/4" machine screws, eight nylon hangers, one mounting bracket w/four #10 x 1" full-threaded screws, and two nuts w/ferrules.

Bennett Hydraulic Tubing 20' Coil

Ref #: 14, Description: Hydraulic Tubing - 20' Coil

Lexan Cover for Hydraulic Power Unit Ref #: 6

Bennett Lower Hinge for Actuator

Description: Actuator Lower Hinge

Sold: Each