Generic

Use for engine intake and wet exhaust connections where bends or long lengths are required. Also good for bilge pump intake/discharge, scupper lines, toilet intake/discharge, and holding tank vent and pump out. Black synthetic rubber tube and cover, reinforced with wire helix imbedded between plies of HD synthetic cord. Resistant to: exhaust fumes, ozone, mild chemicals, antifreeze, salt water, abrasion and odor permeation. Temperature range: -20° F to 200° F continuous, +250° F intermittent. Meets SAE J2006 Type R2.

ID: 5", OD: 5-5/8", Length: 12-1/2'

Use for engine intake and wet exhaust connections where bends or long lengths are required. Also good for bilge pump intake/discharge, scupper lines, toilet intake/discharge, and holding tank vent and pump out. Black synthetic rubber tube and cover, reinforced with wire helix imbedded between plies of HD synthetic cord. Resistant to: exhaust fumes, ozone, mild chemicals, antifreeze, salt water, abrasion and odor permeation. Temperature range: -20° F to 200° F continuous, +250° F intermittent. Meets SAE J2006 Type R2.

ID: 5", OD: 5-5/8", Length: 2'

Use for engine intake and wet exhaust connections where bends or long lengths are required. Also good for bilge pump intake/discharge, scupper lines, toilet intake/discharge, and holding tank vent and pump out. Black synthetic rubber tube and cover, reinforced with wire helix imbedded between plies of HD synthetic cord. Resistant to: exhaust fumes, ozone, mild chemicals, antifreeze, salt water, abrasion and odor permeation. Temperature range: -20° F to 200° F continuous, +250° F intermittent. Meets SAE J2006 Type R2.

ID: 5", OD: 5-5/8", Length: 4'

Use for engine intake and wet exhaust connections where bends or long lengths are required. Also good for bilge pump intake/discharge, scupper lines, toilet intake/discharge, and holding tank vent and pump out. Black synthetic rubber tube and cover, reinforced with wire helix imbedded between plies of HD synthetic cord. Resistant to: exhaust fumes, ozone, mild chemicals, antifreeze, salt water, abrasion and odor permeation. Temperature range: -20° F to 200° F continuous, +250° F intermittent. Meets SAE J2006 Type R2.

ID: 5/8", OD: 61/64", Length: 12-1/2'

Use for engine intake and wet exhaust connections where bends or long lengths are required. Also good for bilge pump intake/discharge, scupper lines, toilet intake/discharge, and holding tank vent and pump out. Black synthetic rubber tube and cover, reinforced with wire helix imbedded between plies of HD synthetic cord. Resistant to: exhaust fumes, ozone, mild chemicals, antifreeze, salt water, abrasion and odor permeation. Temperature range: -20° F to 200° F continuous, +250° F intermittent. Meets SAE J2006 Type R2.

ID: 6", OD: 6-21/32", Length: 12-1/2'

Use for engine intake and wet exhaust connections where bends or long lengths are required. Also good for bilge pump intake/discharge, scupper lines, toilet intake/discharge, and holding tank vent and pump out. Black synthetic rubber tube and cover, reinforced with wire helix imbedded between plies of HD synthetic cord. Resistant to: exhaust fumes, ozone, mild chemicals, antifreeze, salt water, abrasion and odor permeation. Temperature range: -20° F to 200° F continuous, +250° F intermittent. Meets SAE J2006 Type R2.

ID: 7/8", OD: 1-3/16", Length: 12-1/2'

This low profile molded hatch has quick action dogs, collet arm, vent position and smoked acrylic lens.
Trim ring & screen included.

Sizes:
• OD: 19-1/8" x 19-3/8" OD
• Cut Out: 16-7/8" x 16-7/8"
• Flange: 18 7/8" X 18 7/8"


• OD: 20-3/8" x 15-18" OD
• Cut Out: 17-7/8" x 12-7/8"
• Flange: 19 7/8" X 14 7/8"

HATCH COVER PULL ONLY SS

The Sea-Dog Hatch Cover Pull is made of stamped 304 stainless steel.

Size:
• Height: 1-15/16"
• Base diameter: 1-1/4"

"Chrome plated brass and zinc. Keeper is 1-1/2" x 5/8"."

Size: 1-1/2" x 3/4", Fastener: #8

Sold: Each

Description: Hatch Fastener, Base: 1-1/2" x 5/8", Fastener: #8

A: 2-15/16", B: 2-3/16", C: 3/8", D: 1/16", E: 1-3/16", Fastener: #8 FH

"Hatch Hinge, Chrome/Bronze 3" x 1-1/2"

Material: Chrome Bronze, Size: 3" x 1-1/2", Fastener: #8, Pack: 2

Sold: Pack

"Hatch Hinge, Chrome/Zinc 3" x 1-1/2"

Material: Chrome Plated Zinc, Size: 3" x 1-1/2", Fastener: #8, Pack: 2

Sold: Pack

"In case of power failure, this bracket allows you to pull the hatch open 5" in order to remove pull pin for access."

Description: SS Slide Bracket, Non-locking

This low profile molded hatch has quick action dogs, collet arm, vent position and smoked acrylic lens.
Trim ring & screen included.

OD: 22-1/16" x 22-5/16" OD", Cut Out: 19-3/4" x 19-3/4", Flange: 21 7/8" X 21 7/8"

Sold: Each

"For smooth and carpeted surfaces. Chrome plated zinc "T" handle and S.S. stem. Easily installs in a 2-1/2" diameter hole. All have a 3" diameter face plate. DP1 cam bar adjustment 3/4" - 2-3/8", DP4 extra long cam bar adjustment 1/2"-3"."

Description: w/Offset Cam Bar , Type: Lock, Color: White

Sold: Each

The Sea-Dog Stainless Steel Hatch Spring has an internal wire that prevents the spring from being overextended during normal use. Not recommended for applications where hatch will scoop wind while boat is underway and overextend.

Length: 8-5/8", Fastener: "#10 RH or 3/16" pop rivet"

Sold: Each

Hatch Springs are made of formed 7 stamped 304 stainless steel. Ideal for use on lighter hatches, dock boxes and lazarettes. Not recommended for applications where hatch will scoop wind while boat is under way and over-extend spring.

Length: 10-1/8"

Sold: Each

Hatch Springs are made of formed 304 stainless steel with injection molded nylon mounts. Big, heavy-duty spring that is ideal for larger hatches and dock boxes. Strong stainless steel spring with internal safety cable that prevents spring from being overextended during normal use. Mounts heavy-duty molded nylon pads on both ends.

Length: 11-5/8"

Sold: Each

Hatch Spring SS 8-3/4"

• Size: (A) 8-5/8" (B) 1-1/16" (C) 3/4"
• Fastener: #10 RH & 3/16" Pop Rivet
• Internal wire prevents spring from overextending