527-822374 Bravo Gimbal Ring Conversion Kit
This is used to convert standard Bravo gimbal ring to the
HP gimbal ring and bell housing. Note: Trim limit switch can
not be used on HP gimbal ring do to the thickness of the
gimbal ring. You will need to get some mechanical indicators to
see the location of your drive.
|
|
421-05-8033
IMCO Gimbal Ring Kit - Mercury Top Pin
Now you can eliminate the weak link in your drive train and run without the
worry of mechanical failure. The Gimbal Ring gives your drive the strength
it needs. Gimbal Ring Kit Black (Mercury Gimbal) must be used with hydraulic steering
|
|
This Part has options, please click the button below to order.
130-102 + Option(s) M6 / M8 Prop Aerator Kit
This custom prop aerator kit is designed to allow air to the propeller which helps large boats with radical engines come on plane easier. In pleasure applications, the aerators take the load off of the props when maneuvering around docks, and help to prevent engine stalling when engines are shifted into gear. In race conditions, aerators improve throttle response coming out of corners or after hitting down on a big wave by instantly relieving the load off of the propellers. Hose and clamps included.
Requires drilling a 3" diameter hole in the top of the lower drive. Lower stainless piece is cut to fit and must be custom fit to your propeller.
|
|
This Part has options, please click the button below to order.
525-44117A12 Mercruiser Transom Plate Assembly 44117A12
|
|
421-05-8005
IMCO Extreme Advantage HP Gimbal with Outside Steering Kit
Now you can eliminate the weak link in your drive train and run without the
worry of mechanical failure. The HP Gimbal Housing gives your drive the strength
it needs. Check these IMCO, HP Gimbal super features:
- The HP Gimbal Housing uses a thicker than stock casting.
- The HP helmets have been beefed up in all critical areas including the pin
locations that are normally prone to failure.
- The HP Gimbal lower swivel pin is 40% stronger than original.
- The HP Gimbal has a removable bearing pack for easy maintenance.
- The HP Gimbal nameplate can be simply unscrewed for access to the upper
swivel shaft nut, without removing the housing from the transom.
|
|
421-05-100B
IMCO Extreme Advantage HP Gimbal Without Steering
Now you can eliminate the weak link in your drive train and run without the
worry of mechanical failure. The HP Gimbal Housing gives your drive the strength
it needs. Check these IMCO, HP Gimbal super features:
- The HP Gimbal Housing uses a thicker than stock casting.
- The HP helmets have been beefed up in all critical areas including the pin
locations that are normally prone to failure.
- The HP Gimbal lower swivel pin is 40% stronger than original.
- The HP Gimbal has a removable bearing pack for easy maintenance.
- The HP Gimbal nameplate can be simply unscrewed for access to the upper
swivel shaft nut, without removing the housing from the transom.
|
|
602-9F-116 Alpha 1 Gen 2 Mercruiser 6111002LP complete brand new transom plate assembly with trim cylinders. Fits: 1991 to current Alpha 1 Gen 2. Replaces Original Equipment made by Mercruiser part #6-6111002LP.
|
|
528-2000 Bravo Hi-Performance Swivel Shaft
This swivel shaft is made from 174-PH stainless steel and is heat treated for maximum strength. This stainless has the corrosion resistance of 304 stainless steel. By using this shaft, the life of your gimbal ring and gimbal housing seal will be greatly increased. This shaft replaces OEM #98230A1 and #866718A01.
Fits: Alpha Gen II, Bravo I, II, III
|
|
This Part has options, please click the button below to order.
525-866718A01 SHAFT-UPPER Mercruiser 866718A01
|
|
528-3017 HP 3/8" U-Bolt Kit For Bravo Outdrives
This U-bolt exceeds OEM strength with over 6,000 pounds of tensile strength.
The U-bolt is made of 17-4 stainless steel. The nylon insert lock nuts are
made of Monel, an extremely strong material used in military applications.
The U-Bolt kit fits Bravo Gimbal Rings and is an ideal upgrade for heavier
boats and those running high horsepower engines. This upgrade will help to
eliminate gimbal ring and swivel shaft failure in your Bravo outdrive.
Replaces Mercury part numbers 10-805164 (U-bolt) and 11-862903 (Nuts). Fits all Bravo Outdrives.
|
|
130-1035 Hardin Marine's all new stainless steel trim cylinder end caps are the perfect addition to any Imco, Mercruiser Bravo or Alpha One application. Simple, Stunning. Highly Polished 316L Stainless Steel construction and quick, simple easy to install. Get rid of those cheap stock black plastic caps because your boat deserves better. Sure it's Jewelry or Bling, you pick the term, but isn't your boat worth it? Sold Each. Also available in packs of 4.
NOTE: DOES NOT FIT ALPHA GEN II
|
|
130-1036 Hardin Marine's all new stainless steel trim cylinder end caps are the perfect addition to any Imco, Mercruiser Bravo or Alpha One application.Simple, Stunning. Highly Polished 316L Stainless Steel construction and quick, simple easy to install. Get rid of those cheap stock black plastic caps because your boat deserves better. Sure it's Jewelry or Bling, you pick the term, but isn't your boat worth it? 4-PACK.
NOTE: DOES NOT FIT ALPHA GEN II
|
|
130-1025 New High Performance Mercury Urethane Ram Bushings - Kit Includes All 8 Bushings
Hardin Marine has come up with new urethane ram bushings for Bravo outdrives.
They are packaged in kits. They are available in red only and are
recommended for all boats running over 60 mph. Enjoy increased stability
when you need it!
Each kit comes with 8 Urethane Ram Bushings.
|
|
This Part has options, please click the button below to order.
530-803097T1 REPAIR KT-TRANSOM Mercruiser 30-803097T1
Where Used
R/MR ALPHA ONE STERNDRIVE - R/MR/ALPHA ONE (Sterndrive) 1983-1990 |
R/MR ALPHA ONE STERNDRIVE - R/MR/ALPHA ONE (Transom Assembly) 1983-1990 |
|
|
This Part has options, please click the button below to order.
530-803099T1 REPAIR KT-TRANSOM Mercruiser 30-803099T1
|
|
This Part has options, please click the button below to order.
530-8M0095485 REPAIR KT-TRANSOM Mercruiser 8M0095485
|
|
|
|
700-21965 Transom Service Kit with Exhaust Tube & Bellows (Bravo) replaces MerCruiser part # 30-803100T1 and 8M0095485
Kit Contains:
Part # |
MerCruiser # |
Description |
|
Part # |
MerCruiser # |
Description |
700-21905 |
30-60792A4 |
Gimbal Bearing |
|
700-39640 |
16755T1 |
Drive Seal Kit |
700-47130 |
32-43437 |
Water Hose |
|
700-89080 |
74639 |
Shift Cable Bellow |
700-89080 |
74639 |
Shift Cable Bellow |
|
700-89100 |
18654A1 |
Exhaust Bellow |
700-89140 |
86840A3 |
U-Joint Bellow |
|
700-89150 |
78458A1 |
Exhaust Tube |
|
|
This Part has options, please click the button below to order.
530-74639Q02 BELLOWS KIT (Priced Each. Must be sold in quantities of 2) Mercruiser 74639Q02
|
|
This Part has options, please click the button below to order.
530-78458A1 TUBE ASSEMBLY-EXH Mercruiser 78458A1
Supercedes: 78458
|
|