Generic

• Run dry protection up to 30 seconds
• Pump housing connects onto the standard 3" waste outlet
• 6' Power leads with plug may be permanently attached to the vehicle or battery clips may be attached for portability
• Discharge port is a standard garden hose connector and the macerator section grinds waste down to a particle size of 1/8" maximum
• Pump longer distances and empty your holding tanks into a portable tank, toilet, sewer clean-out port or septic tank

Volts: 12, Inlet: 3"

• RV macerator pump can empty a 30 gallon (115 liter) holding tank in 3 minutes
• Grinds waste into small particles for easy disposal
• Self-priming with a flow rate of 13 gpm (49 lpm)
• Pump can be permanently installed for easy holding tank evacuation into a toilet or plumbing clean out access

GPM: 13, Volts: 12, Amps: 16, Inlet: 3", Outlet: 1"

Molded black plastic. Designed with a flange molded into part to fit into hole, hiding raw or cut edges. Mounts with 4 screws. Bulk packaging.

Size: 4-1/4" dia. ", Hole: 2-1/2" dia. ", Case: 12

Sold: Each

Molded black plastic. Designed with a flange molded into part to fit into hole, hiding raw or cut edges. Mounts with 4 screws. Bulk packaging.

Size: 5-5/8" dia. ", Hole: 4" dia. ", Case: 12

Sold: Each

"Positive sealing ball scupper. Seal slotted to fit over 1-1/4" motorwell hole."

:

Sold: Each

Fluidampr Int. Harmonic Balancer Chevy LS1/LS6/LS2

• Material: Steel
• Finish: Black Zinc
• Keyway: None
• Bore Dia. Min/Max: 1.4818 / 1.4828
• Degree Marking Range: None
• OD: 6-1/4"
• Length: 2.637
• Engine Balance: Internal

You can't feel them or hear them, but harmonic vibrations are at work inside every internal combustion engine. That's not good. Similar to glass-shattering forces created by a high pitched note, harmonic vibrations cause metal fatigue and can cause significant power loss because crankshaft harmonics are transmitted to the camshaft and valvetrain. Control this power-robbing force with a Fluidampr harmonic damper that uses race proven vibration damping technology. A high viscosity silicone fluid surrounds a nylon-coated inertia ring inside a laser welded housing. All dampers are coated with a black zinc chromate finish for increased corrosion resistance. Timing marks - every two degrees from 50° BTDC to 10° ATDC with additional marks at 90, 180 and 270. Meets SFI 18.1 specs. Made In The USA.

Fluidampr Int. Harmonic Balancer GM / Chevy 6.2L LT4

• Crankshaft torsional vibration protection across RPM range. 
• Reduce risk of crankshaft failure & wear on critical engine parts. 
• Unleash lost torque and horsepower. 
• Replaceable crankshaft hub. 
• SFI 18.1 certified.
• Made in USA.

The steel damper is finished in a corrosion resistant black zinc chromate, then laser engraved with a Fluidampr – Made in the USA logo and SFI 18.1 credential. The front and rear bolt-on Supercharger and air-conditioning aluminum pulleys have a hard coat anodized finish.

Available in three sizes to fit any GROCO ARG Strainer, flush caps make flushing your raw water cooled equipment a snap. Temporarily replacing your existing strainer cap with a flush cap will allow you to easily connect a Port-O-Flush Jr.^® or garden hose to your system. Use flush caps to flush you raw water cooled equipment with Barnacle Buster^®, fresh water, or to aid in winterizing your system.
NOTE: Not intended to replace your existing strainer cap, for flushing use only.

Fits: Groco ARG 500, 750 & 755 strainers

Available in three sizes to fit any GROCO ARG Strainer, flush caps make flushing your raw water cooled equipment a snap. Temporarily replacing your existing strainer cap with a flush cap will allow you to easily connect a Port-O-Flush Jr.^® or garden hose to your system. Use flush caps to flush you raw water cooled equipment with Barnacle Buster^®, fresh water, or to aid in winterizing your system.
NOTE: Not intended to replace your existing strainer cap, for flushing use only.

Fits: Groco ARG 1500+ strainers

Chrome plated zinc. Sliding lock button. Reverse bevel with flush strike. Flush cup installs in 2" diameter hole. Supplied with black plastic spacer for optional surface mounting.

• Screw size for cup is #8
• case is #6
• OD cup is 2-1/4"
• case is 2-1/16" x 1-3/4"
• For door thickness of 3/4" to 1-1/8"

"For securely "Dogging" (fastening) deck hatches. Chrome plated brass and stainless steel lock nuts. Flush strike. O-ring seals for water resistance. Does not rattle when dogged down. Maximum hatch thickness 2"."

Size: 3-13/16" x 3", Fastener: #8

Sold: Each

"Injection molded ABS. Overall face dimension is 3-5/8" x 3-5/8". Hose/hole size 3". Carded."

Color: White, Fastener: #8 FH

Sold: Each

Material: Chrome Bronze, Size: 3-3/4" x 2-3/4" , Fastener: #8

Material: Chrome Bronze, Size: 3" x 2-1/4" , Fastener: #8

Material: Chrome Zinc, Size: 3" x 2-1/4" , Fastener: #8

Flange: 3" L x 2-1/4" W , Fastener: #6

Flush Mount Drink Holder Black Large

Seadog Flush Mount Drink Holders are constructed of injection molded ABS plastic and are available in a range of sizes. Small and medium models will hold a standard can while the large models will hold a can with a insulated can wrap. The jumbo combination models feature a dual purpose design to hold cans with or without insulated can wraps.

• 4-1/8" Outside Dia x 3-5/8"Inside Dia x 2-5/16"D

FLUSH MNT DRINK HOLDER Black MD

Seadog Flush Mount Drink Holders are constructed of injection molded ABS plastic and are available in a range of sizes. Small and medium models will hold a standard can while the large models will hold a can with a insulated can wrap. The jumbo combination models feature a dual purpose design to hold cans with or without insulated can wraps
Size: 2-7/8"Dia x 3"D

Flush Mount Drink Holder Black Small

Seadog Flush Mount Drink Holders are constructed of injection molded ABS plastic and are available in a range of sizes. Small and medium models will hold a standard can while the large models will hold a can with a insulated can wrap. The jumbo combination models feature a dual purpose design to hold cans with or without insulated can wraps.

• Size: 2-7/8"Dia x 2"D

FLUSH MNT DRINK HOLDER Black XL

Seadog Flush Mount Drink Holders are constructed of injection molded ABS plastic and are available in a range of sizes. Small and medium models will hold a standard can while the large models will hold a can with a insulated can wrap. The jumbo combination models feature a dual purpose design to hold cans with or without insulated can wraps.
Size: 3-5/8"/2-7/8"Dia x 3-1/4"D