Bluewater Enterprises

Relays and Bi-Stable relays such as a Remote Battery Switch or Charge Control Relay exhibit similar behavior as above only have low amperage requirements in some cases less than 250 milliamps not even 1 Ampere required by the device. But the bounce or magnitude of the resulting EFT (electrical fast transient) when being switched can be excessively high.

LED Lights, not all but some have internal power controllers. Others have basic switching drivers and have high noise or EFT (electrical fast transients) present while operating and when being switched on of a high magnitude and are expected; some are harsher than others. Could be very small LED’s or large spreader LED lights; either could have similar negative electronic behavioral effects. Again, even ones that consume less than 1 amp could be a significant contributor to faults.

None of the above has to do with the quality of a particular manufacturer it simply is an inherent characteristic of the referenced devices. However, there is a simple solution. Again, typically there is one switch or device when being turned on or operating that is attributing to In-Rush fault indication and easily identified. Typically, when being turned on or off however in the LED example it may not occur until after a long period of operation when voltage is depleted or temperature increases. In both examples B & C a 16V 1000uF electrolytic capacitor Part ID: 1406-000-001 can be installed across the Line V+ and Ground near the switch to correct the issue creating the fault.

This is a replacement plug with lead for the 516-9150-XXXX 19mm switches.

This tool allows you to crimp Deutsch connector pins to 14-24 AWG Wire

Diode for use with Bluewater push button electronic switches.

Double USB outputs 5VDC/2.1A, enough to charge iPhones, iPads and almost all other devices. Power Socket rated at 12 volts, 16 amps. Includes screws and connectors. Injection molded nylon.

A: " 3-1/2", B: " 1", C: " 1-5/8", Input: 12V-24V, Output: DC 5V/2.1A

Sold: Each

These dummy plugs are used in the switch Deutsch connectors when you are not using one of the wire holes.

Function Labels for 19MM Push Button Switches 

Identifying the function of each push button switch is simple with the interchangeable 3M adhesive backed actuator PU Dome Backlit Labels. These labels are used when using translucent actuator buttons that allows the LEDs in the switch body to pass light through the label. The result is excellent visibility at night. There are over 100 Switch Function Icons to choose from.

• Over 100 Interchangeable 3M Adhesive Backed PU Dome Backlit Function Icon Labels to choose from.
• Light passes through clear part of label
• Used with 19mm switches with the translucent label option

Function Labels for 22MM Push Button Switches 

Identifying the function of each push button switch is simple with the interchangeable 3M adhesive backed actuator PU Dome Backlit Labels. These labels are used when using translucent actuator buttons that allows the LEDs in the switch body to pass light through the label. The result is excellent visibility at night. There are over 100 Switch Function Icons to choose from.

• Over 100 Interchangeable 3M Adhesive Backed PU Dome Backlit Function Icon Labels to choose from.
• Light passes through clear part of label
• Used with 22mm switches with the translucent label option

Dual USB Port Charger Socket

• 12V DC Dual USB Charger dash mount with protective cap
• Twin USB 2.0 Female ports
• Compatible with popular mobile devices
• Easy to use
• LED lit by blue LED's
• Max output charge 4.8A DC total (2.4A Per Port)
• Output Voltage 5V DC+/- 5%
• Hole Size: 1"
• Thread Length: 1-5/8"

Dual USB Port Charger Socket

• 12V DC Dual USB Charger dash mount with protective cap
• USB Female port
• USB-C Female port
• Compatible with popular mobile devices
• Easy to use
• Max output charge 4.8A DC total (2.4A Per Port)
• Output Voltage 5V DC+/- 5%
• Hole Size: 1"
  

• Label Set included.
• Clear insulating cover with label recesses accept Small Format Labels

• Clear insulating cover with label recesses accept Small Format Labels
• Label Set included.
• Fuses not included.

• Clear insulating cover with label recesses accept Small Format Labels
• Label Set included.
• LED Indicator Lights

• Clear insulating cover with label recesses accept Small Format Labels
• Label Set included.
• Breakers not included.

The Motorized Battery Switch has two modes of operation. Auto and Manual. There is a LED located on the battery switch to indicating Battery Switch Status.

Auto Operation: The Battery Switch moves from a state of "Auto Off" to "Auto On" when the remotely mounted switch is turned on. During the time that the battery switch is in "Auto On" mode, the "Auto On" LED is illuminated. Auto operation of the battery switch is not possible whilst in manual mode. If auto operation is attempted, the LED will flash for 3 seconds then stop. Knob must be returned to "Auto Off" before normal auto operation can continue.

Manual Operation: The automatic operation of this battery switch can be overridden at anytime by depressing the control knob and turning clockwise towards the "Man On" position or counter clockwise towards the "Man Off" position. During the time that the Battery switch is in "Man On" mode, the "Man On" LED is illuminated.

The Motorized Battery Switch has two modes of operation. Auto and Manual. There is a LED located on the battery switch to indicating Battery Switch Status. This is a Ground activated Battery Switch, Same as 516-9805-006-1 but this is activated by a ground, whereas the 516-9805-006-1 is activated by +12V.

Auto Operation: The Battery Switch moves from a state of "Auto Off" to "Auto On" when the remotely mounted switch is turned on. During the time that the battery switch is in "Auto On" mode, the "Auto On" LED is illuminated. Auto operation of the battery switch is not possible whilst in manual mode. If auto operation is attempted, the LED will flash for 3 seconds then stop. Knob must be returned to "Auto Off" before normal auto operation can continue.

Manual Operation: The automatic operation of this battery switch can be overridden at anytime by depressing the control knob and turning clockwise towards the "Man On" position or counter clockwise towards the "Man Off" position. During the time that the Battery switch is in "Man On" mode, the "Man On" LED is illuminated.

This tool allows you to easily install the nut on the back of your switch. Can be used with 1/4" drive ratchet.

Additional Details:

• Fits: Bravo drives

Interchanges/Replaces

GLM

• 86310

Mallory

• 9-76503

Mercruiser Stern Drive

• 16755
• 16755A1
• 16755Q1

Polished Stainless Steel Quick Pin Fender Cleat with Soft Tie Loop

• All CNC MACHINE STAINLESS STEEL 
• SOFT TOUCH TOP QUICK RELEASE STAINLESS BUTTON  
• SPRING LOADED STAINLESS BASE FOR QUICK RELEASE 
• SOFT TIE LOOP FOR ATTACHMENT OF FENDERS 
• PROTECT NYLON WASHER ON QUICK RELEASE PIN
• 3/4" HOLE REQUIRED FOR INSTALLATION
• ROPE IS 6" LONG. 1/4" IN DIAMETER

*** NOT INTENDED FOR MOORING ***