Accessories - Trailer Accessories

1/2" Stainless Eyelet

These are high grade stainless eyelets in 1/2" diameter. The eyelets can also be used on the transoms or bow of boats for tie downs or tow hooks. 3" of thread length.

3/8" Stainless Eyelet

These are high grade stainless eyelets in 3/8" diameters. The eyelets can also be used on the transoms or bow of boats for tie downs or tow hooks. 2-3/4" Thread Length.

Bow Eye Chrome Zinc 3/8"

The Seadog Bow Eye has a die cast zinc chrome plated head and a galvanized shaft.

• 3/8" NC thread
• 2-9/16" bolt length
• 5-1/8" total length

Bow Eye SS 1/2" x 3-7/16"

Seadog Stainless Steel Bow Eyes come with adjustable finished nuts for a strong and secure hold.

• Plate Size: 3" x 3/4"

Bow Eye SS 3/8" x 3-1/2"

Seadog Stainless Steel Bow Eyes come with adjustable finished nuts for a strong and secure hold

Coupler Lock Standard Brass

Fulton Coupler Locks attach to the coupler on a trailer to prevent theft when not attached to a receiver. The standard and adjustable models come in brass while the universal model comes in hi-vis yellow. All locks come with 2 keys.

Coupler Lock Universal Yellow

Fulton Coupler Locks attach to the coupler on a trailer to prevent theft when not attached to a receiver. The standard and adjustable models come in brass while the universal model comes in hi-vis yellow. Locks come with 2 keys.

COUPLER LOCKING PIN GALV 1/4"

The Seadog Coupler Pins have a steel electro galvanized construction.

Features:
• Size: (A) 1/4" (B) 3" (C) 1-13/16" (D) 7/16" (E) 13/16"

Coupler Locking Pin Galv 5/16"

The Seadog Coupler Pins have a steel electro galvanized construction.

• Size: (A) 5/16" (B) 3" (C) 2" (D) 5/8" (E) 7/8"

D-Shackle SS 5/16"

The Seadog Stainless Steel D-Shackles have an investment cast 316 stainless steel construction that withstands the marine environment.

• Size: (A) 5/16" (B) 5/8" (C) 1-1/8"

Hitch Pin and Clip 5/8"

Fulton Hitch Pin and Clips feature a grooved style hitch pin and clip for use with 2" and 1-1/4" square receivers.

• 5/8" Hitch pin for 2" square receivers

LED CLEAR/SIDE LIGHT RECT. AMBR

Wesbar Waterproof Rectangle Side/Clearance Lights feature a snap lock base mount

LED CLEAR/SIDE LIGHT RECT. AMBR

Wesbar Waterproof Rectangle Side/Clearance Lights feature a snap lock base mount.

LED CLEAR/SIDE LIGHT RECT. RED

Wesbar Waterproof Rectangle Side/Clearance Lights feature a snap lock base mount

Bow Eye SS 3/8" x 1-1/2"

Seadog Stainless Steel Bow Eyes come with adjustable finished nuts for a strong and secure hold.

• 2-1/4" x 3/4"

Bow Eye SS 7/16" x 3-1/2"

Seadog Stainless Steel Bow Eyes come with adjustable finished nuts for a strong and secure hold.

• 3" x 3/4"

Trailer Plug Adapter 7 to 4

Seadog 4-Wire Trailer Wire Accessories are made from injection molded PVC.

HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness - 1,000 psi

Specs:
• Application: single- and tandem-axle trailers (up to 7,000 lbs) with drum brakes
• Maximum output pressure: 1,000 psi
• Power: 12V DC
• Hydraulic port size: 3/16"
• Actuator dimensions: 11-3/4" long x 3" wide x 7-3/8" tall
• Actuator wire configuration:
  • Black: 12-volt power
  • Blue: brake controller
  • Yellow: breakaway
  • White: ground
• Battery capacity: 5 amp-hours
• Breakaway battery case dimensions: 5-7/16" long x 4-1/4" wide x 4-1/4" tall
• Battery dimensions: 3-7/8" long x 3-1/2" wide x 2-11/16" tall
• Breakaway switch lead wire length: 7-1/2"
• Trailer connector length: 6'
• Trailer connector wire gauges:
  • Black/white: 10 gauge
  • Blue: 12 gauge
  • Brown/red/green/yellow: 14 gauge
• Junction box dimensions: 6-3/4" long x 3-1/2" wide x 2-1/4" tall
• Split wire loom length: 6'

Note: Do not power wash the HydraStar actuator or take it through a commercial car wash. High-pressure water may damage the seals on the actuator.

The HydraStar electric-over-hydraulic trailer brake actuator applies pressure to your trailer's hydraulic brake system in response to the electrical signals sent from your in-cab brake controller. As a result, your trailer's hydraulic brakes will be activated every time you apply the brakes in your vehicle or press the manual override on your controller. This setup is ideal for boat trailers because you will get responsive hydraulic braking, which you control conveniently from inside your vehicle with your electric brake controller.

HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness - 1,200 psi

Specs:
• Application: single- and tandem-axle trailers (up to 7,000 lbs) with drum brakes
• Maximum output pressure: 1,200 psi
• Power: 12V DC
• Hydraulic port size: 3/16"
• Actuator dimensions: 11-3/4" long x 3" wide x 7-3/8" tall
• Actuator wire configuration:
  • Black: 12-volt power
  • Blue: brake controller
  • Yellow: breakaway
  • White: ground
• Battery capacity: 5 amp-hours
• Breakaway battery case dimensions: 5-7/16" long x 4-1/4" wide x 4-1/4" tall
• Battery dimensions: 3-7/8" long x 3-1/2" wide x 2-11/16" tall
• Breakaway switch lead wire length: 7-1/2"
• Trailer connector length: 6'
• Trailer connector wire gauges:
  • Black/white: 10 gauge
  • Blue: 12 gauge
  • Brown/red/green/yellow: 14 gauge
• Junction box dimensions: 6-3/4" long x 3-1/2" wide x 2-1/4" tall
• Split wire loom length: 6'

Note: Do not power wash the HydraStar actuator or take it through a commercial car wash. High-pressure water may damage the seals on the actuator.

The HydraStar electric-over-hydraulic trailer brake actuator applies pressure to your trailer's hydraulic brake system in response to the electrical signals sent from your in-cab brake controller. As a result, your trailer's hydraulic brakes will be activated every time you apply the brakes in your vehicle or press the manual override on your controller. This setup is ideal for boat trailers because you will get responsive hydraulic braking, which you control conveniently from inside your vehicle with your electric brake controller.

HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness - 1,600 psi

Specs:
• Application: single- and tandem-axle trailers (up to 7,000 lbs) with drum brakes
• Maximum output pressure: 1,600 psi
• Power: 12V DC
• Hydraulic port size: 3/16"
• Actuator dimensions: 11-3/4" long x 3" wide x 7-3/8" tall
• Actuator wire configuration:
  • Black: 12-volt power
  • Blue: brake controller
  • Yellow: breakaway
  • White: ground
• Battery capacity: 5 amp-hours
• Breakaway battery case dimensions: 5-7/16" long x 4-1/4" wide x 4-1/4" tall
• Battery dimensions: 3-7/8" long x 3-1/2" wide x 2-11/16" tall
• Breakaway switch lead wire length: 7-1/2"
• Trailer connector length: 6'
• Trailer connector wire gauges:
  • Black/white: 10 gauge
  • Blue: 12 gauge
  • Brown/red/green/yellow: 14 gauge
• Junction box dimensions: 6-3/4" long x 3-1/2" wide x 2-1/4" tall
• Split wire loom length: 6'

Note: Do not power wash the HydraStar actuator or take it through a commercial car wash. High-pressure water may damage the seals on the actuator.

The HydraStar electric-over-hydraulic trailer brake actuator applies pressure to your trailer's hydraulic brake system in response to the electrical signals sent from your in-cab brake controller. As a result, your trailer's hydraulic brakes will be activated every time you apply the brakes in your vehicle or press the manual override on your controller. This setup is ideal for boat trailers because you will get responsive hydraulic braking, which you control conveniently from inside your vehicle with your electric brake controller.