Your shopping cart is currently empty.
Items Per Page:
Waterproof RGBW Bluetooth LED Light Controller for Plash Lights
513-BT-60W-RGBW
This controller will operate both normal RGB (Red, Green, & Blue) and RGBW (RGB + White).
PlashLights waterproof Bluetooth controller is operated via a mobile phone app to turn on/off, adjust the brightness or color, adjust color temperature, and change preset color patterns. There are a variety of lighting patterns to choose from.
The operation is very simple with mobile phone control (IOS or Android). Your phone is not needed when a switch is installed as the lights will defer to the last setting when powered on (Example: If you have them on a blue stobe pattern and turn the power of at a switch or the Perko, when power is applied at a later date the lights will be on blue strobe). Basically, your phone is only required to change the color or patterns.
- Requires download of PlashLights APP (FREE)
- Simple to mount with a tab on each side
- IP67 Rated Enclosure = Waterproof
- Easily control and synchronize up to 240 Watts of lighting
- 15A when RGB used (5A/per channel)
- 20A when RGB+W used (5A/per RGB channel & 5A white)
- Compatibility: bluetooth 4.0 (bluetooth phones of 4.0 or above)
- Supports mobile phone system: IOS 6.0 android 4.3 or above
- Operating Voltage: 12~24V DC
- Software language: English
- Control distance: 65 feet
- Size: 3-13/16" long x 1-1/4" tall x 1-15/16" wide
- Working temperature: - 4°F to 145°F
Control Operations:
- Instructions included on APP
Includes Multi-Zone Sync Feature:
- Control multiple zones with multiple controllers as they will all sync together (each controller is sold separately)
Notes:
- Do not place RGBW controller inside a metal container as it will block the signal.
- Double check your incoming voltage as this controller cannot accept reverse polarity, AC, or DC voltage over 24V.
LED Trim Indicator Adapter for Smartcraft Systems
137-8656
Allows the connection of an LED indicator, to any SmartCraft-equipped boat (sterndrives or outboards). The adapter will maintain the isolated PCM grounds and allow normal engine operation (no faults or Guardian modes). With the Adapter you will be able to have the LED indicator and have the trim visible on VesselView or a Garmin/Simrad display. No wires to splice or crimp, it all plugs in to the Mercury harness.
3/4" Drain Plug 27W Underwater LED Light
513-PL-DP-27W-3/4 + Option(s)
Our high intensity LED drain plug lighting allows for a simple installation for underwater lights in a standard 1/2" or 3/4" NPT drain thread, this version is 3/4". Each light is built with a 60" wire tail and a simple two wire (red & black) wiring configuration unless you choose RGB. Then it must utilize an RGB controller (sold separately) to provide the ability to change colors, patterns, etc. No other light manufacturer produces such a great output for underwater lighting for as reasonable price. When you hold this light you will understand the quality by the weight of the 316 stainless steel housing, but more importantly when you turn this light on you will see the quality by the light output.
- Night activities
- Swimming
- Safety for loading and unloading at night
- Great for attracting fish on your evening trips
- Easily be seen out on the water
- Extreme intensity for showing off anytime of the day
- An easy way to help your sight when loading / unloading on lifts in the dark
What a simple way to turn heads at the dock. You will be the talk of the marina or the boat ramp.
FEATURES
- 3,250 Lumens MAX (each color varies)
- 30° Emitting Angle
- Fits standard 3/4" NPT drain opening
- Input Voltage: DC 12V (9V to 32V Max.)
- Current Draw: 2.2A @ 13.5VDC
- 50,000+ Hour Life
- 316 Stainless Steel Housing (Polished)
- Factory Sealed Housing - IP68 Rated
- Lifetime Warranty
- Underwater Use Only
- RGB Controller Sold Separately
- Includes one (1) light with 5ft of power wire
1/2" Drain Plug 27W Underwater LED Light
513-PL-DP-27W-1/2 + Option(s)
Our high intensity LED drain plug lighting allows for a simple installation for underwater lights in a standard 1/2" or 3/4" NPT drain thread, this version is 1/2". Each light is built with a 60" wire tail and a simple two wire (red & black) wiring configuration unless you choose RGB. Then it must utilize an RGB controller (sold separately) to provide the ability to change colors, patterns, etc. No other light manufacturer produces such a great output for underwater lighting for as reasonable price. When you hold this light you will understand the quality by the weight of the 316 stainless steel housing, but more importantly when you turn this light on you will see the quality by the light output.
- Night activities
- Swimming
- Safety for loading and unloading at night
- Great for attracting fish on your evening trips
- Easily be seen out on the water
- Extreme intensity for showing off anytime of the day
- An easy way to help your sight when loading / unloading on lifts in the dark
What a simple way to turn heads at the dock. You will be the talk of the marina or the boat ramp.
FEATURES
- 3,250 Lumens MAX (each color varies)
- 30° Emitting Angle
- Fits standard 1/2" NPT drain opening
- Input Voltage: DC 12V (9V to 32V Max.)
- Current Draw: 2.2A @ 13.5VDC
- 50,000+ Hour Life
- 316 Stainless Steel Housing (Polished)
- Factory Sealed Housing - IP68 Rated
- Lifetime Warranty
- Underwater Use Only
- RGB Controller Sold Separately
- Includes one (1) light with 5ft of power wire
Starting From:
$298.99 This Part has options, please click the button below to order.
Underwater LED Light Bars
730-ULEDL + Option(s)
Underwater LED Light Bars, 4, 6 & 10 LED Models
- Operating Voltage: 9 to 36 Volts DC (brightness does not change)
- Internal digital switching power supply operates at 94% efficiency
- Housing Materials: Passivated 316 Stainless Steel with Polycarbonate Lens
- Standard Cable Length: 20 ft
- Lamp Life: 40000 Hours
- Warranty: 2 Years
Adjustable Position LED Indicators
730-ALEDI
Adjustable LED Indicators can be applied to a wide range of applications:
Tabs • Drives • Jackplates • Rudder indicators • Water level • Fuel Level
These state-of-the-art indicators by Livorsi Marine, Inc. are capable of reading CAN Bus protocols such as SmartCraft® (with Gateway), NMEA 2000® and J1939, as well as 0-5 volt or resistive-type (ohms) inputs. The technology used for these indicators can be applied to a wide range of applications such as trim tabs, drives, jackplates, rudder indicators, water level, or fuel level.
The LED position indicators eliminate the need for mechanical 33C cables which are typically used for drive and tab indication. These cables have a tendency to deteriorate, will fail over time, and are inaccurate due to lost cable motion. With the Adjustable Position LED indicators, mechanical cables are replaced by more reliable network wiring that allows 'plug n play' connectivity into existing tab or drive position sensors.
If you do not have drive trim or tab sensors, we have the solution. For applications or retrofits that do not have electronic position sensors, Livorsi can provide you with a mechanical to electronic converter solution so that you may take advantage of the accuracy and benefits of Livorsi's LED Indicators.
What sets these displays apart from anything else is the single middle green LED. During calibration, this LED display can be set to indicate 50% of actuator travel, fuel level or whatever you are monitoring. What makes it so special is that it allows you to establish the optimum running angle - or sweet spot (not at 50%), to dial-in the vessel for optimal running efficiency so the novice boater always runs at the correct trim.
No matter what information you are looking to display (fuel level, drive trim, tab position, etc.), the data is brought into the communication network (Rx) with 'plug n play' harnessing and is received via the network cable to the LED indicator for display. The LED indicator can also transmit (Tx) this information via CAN bus to other compatible displays such as Garmin, Lowrance or Raymarine via NMEA 2000®, SmartCraft® (with Gateway) or J1939 protocols. If your boat is already transmitting (Tx) NMEA 2000® data (tabs, drives, fuel level, water level, rudder angle, etc.), simply plug the indicator into the NMEA 2000® backbone to begin displaying the desired feature on the indicator.
The super bright LED's can be seen in direct sunlight even with polarized sunglasses. With a range of 250 brightness intensity levels, you are guaranteed the best view possible, day or night. We accomplish this with the use of an ambient light sensor which provides automatic adjustment of the LED brightness according to available light conditions.
Setup of the indicator is performed via the proximity/ambient light sensor located on the front of the unit. Simple to follow and easy to use step-by-step instructions are included to ensure installation and setup is a snap.
By setting the 'running point', the indicator can more accurately track the entire range of operation, giving more resolution than if only a high and low point were known.
In order for these new indicators to function, there must be either an electronic sender to transmit the signal, or a mechanical to electrical device to convert the mechanical operation into an electronic voltage or resistance, which will ‘feed’ the signal to the indicator. Many of today’s tabs, drives, jackplates, fuel or water tanks, or rudders already have a sender on it. These versatile indicators can be used with a wide variety of senders such as voltage, resistance, or CAN bus NMEA 2000®, SmartCraft® or SAEJ1939 protocols. We have many ideas to adapt senders for these devices. Let us know your situation, and we will determine the best solution for your application.
The type of sender used whether voltage, resistance, or CAN bus must be known at the time of order with respect to how the indicator will be programmed to read the type of connection used.
BECAUSE OF THE ADVANCED NATURE OF THESE INDICATORS, THEY CANNOT BE ORDERED ONLINE. PLEASE CALL US TO RECEIVE A QUOTE.
WE WILL NEED A COMPLETED BUILD SHEET WHICH YOU CAN OBTAIN HERE: BUILD SHEET
RGB Spectrum LED Cockpit / Cabin Light
516-1005
Don't settle for just one color from your LED lights! This cockpit / cabin light panel does it all! When paired with WiFi Control Box and your iPhone or Android smartphone, these lights can change into an array of colors! Without the WiFi box, they can also be wired to shine permanently in multiple combinations (see wiring specs).
- Hole Cut-Out for cable: 9mm (3/8″)
- Hole cut-Out for connector: 14mm (5/8″)
- The diameter of the light is: 2 3/4"
- Material: Chemically resistant optical polymer body
- Cockpit/Cabin Light, NOT for underwater use.
RGB Spectrum Cabin Strip LED Lights
516-10 + Option(s)
Don't settle for just one color from your LED lights! These UL approved LED light strips do it all! When paired with WiFi Control Box and your iPhone or Android smartphone, these lights can change into an array of colors! Without the WiFi box, they can also be wired to shine permanently in multiple combinations (see wiring specs). These LED strips range from 3-27 Feet and can be cut to fit perfectly.
It's easy to create energy-efficient, innovative accent lighting and general illumination for your boat, dock, trailer or truck with LED strip lighting. We offer a huge selection of RGB color changing LED light panels and LED strip lights that will give your boat and more the visual appeal to create a huge waves. Virtually all our LED strips are UL-listed, so you know it's safe, and versatile.
Hardin Marine Stainless Steel LED Navigation Lights (Pair)
516-1000
Stainless Steel Elliptical Easy Install LED Navigation Light Kit - Port and STBD Sides (Green & Red)
Don't let the size of these lights fool you! Despite its minute size, these L.E.D navigation lights shine brighter than regular bulbs. L.E.D. bulbs last longer, shine brighter and are more energy efficient than standard bulbs. These elliptical navigation lights mount flush into fiberglass for a seamless look, and make a great alternative to the "bug-eyed" pop-up lights. These lights are designed to be mounted on a vertical surface, to allow the light pattern to be unobstructed from view. Unlike other brands these Led Navigation Lights by Hardin Marine are easy to install with a simple round hole cut rather than oval (see photos).
For use on boats up to 65 feet. LED Navigation lights are smaller, brighter and more power efficient than old style Nav lights that use and incandescent bulb. This means longer life and less energy use, and with Hardin's easy install lights, putting them in is a breeze! The stainless steel housing provides increased resistance to corrosion, making these a perfect fit in the marine environment.
- Marine grade polished 316L stainless steel
- USCG Certified
- USCG approved 2 nautical miles
- Overall width is 3-1/4" and length is 1-3/4"
- The housing is 3/4" thick from the mounting flange.
- For use on boats up to 65 feet.
LED Navigation Light Adapter Plates
516-1004
LED Navigation Light Adapter Plates
These are packaged as pairs. This will fit both Hardin & Livorsi navigation lights. These are adapter plates only, lights sold separately!
Note: This replaces 730-LEDNLAP.
LED Boat Drain Plug - 1/2" NPT Stainless Steel (Color RGB Option)
620-06702
- One model, set to any of these many colors: Red, Blue, Green, Yellow, Teal, Purple, White
- OR: Hook up our WIFI control box and control with your phone!
- No wires on the plug! Easy to use unlike other models that wire the plug.
- 1/2" NPT Stainless Steel Plug
- Easy to install base
- Over 2000 Lumens
Yet another Hardin Marine first in a high quality cast stainless steel bilge drain plug loaded with ultra bright sealed LED lights with a maximum light output of up to 28LM/WATTS. This unit is a the standard industry size and retrofits most standard drain plug receivers today and a 1/2 NPT plug is included. The unit can be wired for use a Red, Blue, Green, or standard White color or add the Hardin RGB control box and switch between color options via an iPhone App on the fly! Unlike competing LED drain plugs, the Hardin's LED's are wired to the base NOT the plug.
LED Lighted Dual USB Port Charger Socket
516-3000-1012
Dual USB Port Charger Socket
- 12V DC Dual USB Charger dash mount with protective cap
- Twin USB 2.0 Female ports
- Compatible with popular mobile devices
- Easy to use
- LED lit by blue LED's
- Max output charge 4.8A DC total (2.4A Per Port)
- Output Voltage 5V DC+/- 5%
- Hole Size: 1"
- Thread Length: 1-5/8"