Glenwood Marine

Magnaflow Cam Driven Water Pump

The "Magnaflow" is a self-priming, one-inch cam-driven water pump featuring chrome/brass construction, friction minimizing ball bearings, long lasting ceramic seals and a tough neoprene impeller To accommodate a variety of engine types the "Magnaflow" comes standard with a large 3/4" hose inlet and a pair of 1/2" threaded pipe outlets Every inboard engine needs the best cooling system available Turbocharged to "stocker".. ski boat to cruiser, the new "Magnaflow" has the capacity and performance you're looking for in a quality marine water pump.

Magnaflow Front Cover O-Ring

Magnaflow Shaft Seal Kit

Brass seal ID 0.65", OD 1.13".

White seal ID 0.625", OD 1"

• For Log Manifolds 
• 5" Outside Diameter 
• 3" Inside Diameter 
• 2-15/16" Bolt Hole to Bolt Hole (Adjacent)
• 4-1/8" Bolt Hole to Bolt Hole (Across)
• Sold Each

Master Repair Kit - No Impeller

Note: Fits the 500-1000 Megnaflow pump only.

429-460 Ford

This is the rear part of the motor mount set most commonly used today in jet boats and V drives.  All rear mounts include mount feet.

429-460 Ford

This heavy duty cast aluminum mount is by far one of the most widely used engine mounts in jet boats and V drives today.  All front mounts include mount feet.

Motor Mount 455 Olds & Pontiac

Small & Big Block Chevy

This is the rear part of the motor mount set most commonly used today in jet boats and V drives.  All rear mounts include mount feet. This fits stringer widths from 22" to 26".

Small Block Chevy

This heavy duty cast aluminum mount is by far one of the most widely used engine mounts in jet boats and V-drives today All front mounts include mount feet. Adjustable to fit stringers 22" - 26"

• 455 Oldsmobile.
• 1/2" NPT.
• Replaces stock thermostat housing.
• Polished Aluminum.
• Thermostat will NOT fit inside.
  

Polished Water Pump Cover Plate - 429-460 Ford

These cover plates are designed to cover the OEM water pump area and allow cooling water to enter the engine through the provided 1/2" NPT inlet holes. Includes bolts and gaskets.

Polished Water Pump Cover Plate - 455 Olds

These cover plates are designed to cover the OEM water pump area and allow cooling water to enter the engine through the provided 1/2" NPT inlet holes. Includes bolts and gaskets

Power Take Off Adapters - 455 Olds 1310 Flexplate

Uses 3/8-24 bolts on 2" x 2-3/8" centers

These flanges bolt on the flywheel and accept 1310 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.

Need help choosing your new PTO flange? Check out this handy tutorial!

Power Take Off Adapters - 455 Olds 1350 Flexplate

Uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers

These flanges bolt on the flywheel and accept 1350 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.

Need help choosing your new PTO flange? Check out this handy tutorial!

Power Take Off Adapters - 460 Ford 1310 Flexplate

Uses 3/8-24 bolts on 2" x 2-3/8" centers

These flanges bolt on the flywheel and accept 1310 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.

Need help choosing your new PTO flange? Check out this handy tutorial!

Power Take Off Adapters - 460 Ford 1350 Flexplate

Uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers

These flanges bolt on the flywheel and accept 1350 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.

Need help choosing your new PTO flange? Check out this handy tutorial!

Power Take Off Adapters - Chevy 1310 Flexplate

Uses 3/8-24 bolts on 2" x 2-3/8" centers

Fits Small Block Chevy with a two piece rear main seal and all Big Block Chevy . These flanges bolt on the flywheel and accept 1310 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.

Need help choosing your new PTO flange? Check out this handy tutorial!

Power Take Off Adapters - Chevy 1310 Flywheel

Uses 3/8-24 bolts on 2" x 2-3/8" centers

Fits Small Block Chevy and Big Block Chevy with a two piece rear main seal. These flanges bolt on the flywheel and accept 1310 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.

Need help choosing your new PTO flange? Check out this handy tutorial!

Power Take Off Adapter - Chrysler 6 Bolt 1350 Flywheel

Uses 7/16-20 bolts on 2-3/8" x 2-7/8" centers

These flanges bolt on the flywheel and accept 1350 spicer drivelines.  There are many more available, just call us. These power take offs are needed when attaching your drive shaft to your engine.